List of electrical characteristics of single collision domain segment "slow speed" network buses:
Name | Multidrop | Max nodes | Electrical type | Cable type | Max bitrate [kbit/s] | Length at max bitrate | Max length [m] | Bitrate at max length |
---|---|---|---|---|---|---|---|---|
EIA-485 (UART based) | Y | 256 | EIA-485 | Twisted pair | 1000 kbit/s | 1330 m | 64 kbit/s | |
SCSI-1/2 | Y | 8 | Open collector | Ribbon cable | 20 000 kbit/s | 3 m | 6 m | 5 Mbit/s/ch |
SCSI Ultra2 | Y | 16 | Differential | Ribbon cable with twisted pairs | 40 000 kbit/s | 12 m | ||
LIN[1] | Y | 16 | Open collector | open collector with pull-up to 12V car supply | 19.2 kbit/s | 40 m | ||
SIOX | Y | 62 | 19.2 kbit/s | |||||
I²C | Y | 127 or 1023 | Open collector | 5000 kbit/s | 7.6 m | |||
SMBus | Y | 128 | Open collector | 100 kbit/s | ||||
PMBus | Y | 128 | Open collector | 400 kbit/s | ||||
10BASE5 | Y | 100 | Single ended | RG-8X coaxial | 10 000 kbit/s | 500 m | 500 m | |
10BASE2 | Y | 30 | Single ended | RG-58 coaxial | 10 000 kbit/s | 185 m | 185 m | |
CAN | Y | 128 | ISO 11898-2 Differential | Twisted pair | 1000 kbit/s | 40 m | 1000 m[2] | 50 kbit/s |
DMX512-A | N | 32 | EIA-485 | Twisted pair 120 Ω[3] | 250 kbit/s | 548 m | 548 m (1800ft.)[4] | 250 kbit/s |
DCC | Y | 127 | Single ended | 5 kbit/s | ||||
RS-232 | N | 2 | Single ended | 128 kbit/s | 1.5 m (approx) | 15 m | 19.6 kbit/s | |
PSI5 | Y | Twisted pair | 189 kbit/s | 12 m (approx) | ||||
1-Wire | Y | 248 | Open collector | Single conductor, with ground | 16.3 kbit/s | 300 m | ||
X10 | Y | 256 | Power line | 0.05 kbit/s / 0.06 kbit/s | ||||
FlexRay | Twisted pair | 20 000 kbit/s | ||||||
SENT[5] | N | 2 | Single ended | Single conductor, with 5 V power supply and ground | async. transmission,
min. 39.216 kbits/s |
5 m | ||
SPC[6] | Y | 5 | Single ended or | Single conductor, with 5 V power supply and ground, shielded when using higher speeds | sync. and async. transmission,
variable up to ~150 kbit/s |
~0.5 m | 5 m | same as SENT |
I3C | Y | 127 | 12 500 kbits/s | |||||
SPI | Y | variable up to ~10000 kbit/s
(depends strongly on physical setup) |
||||||
The number of nodes can be limited by either number of available addresses or bus capacitance. None of the above use any analog domain modulation techniques like MLT-3 encoding, PAM-5 etc.
PSI5 designed with automation applications in mind is a bit unusual in that it uses Manchester code.
See also
[edit]- Multidrop bus
- Characteristic impedance
- Category 5 cable
- Telegrapher's equations
- Single-ended signaling
- Network segment
- CEBus
- KNX (EIB)
References
[edit]- ^ "LIN Standards (older versions are free to download, newer to be bought on ISO web site)". www.lin-cia.org. Retrieved 2019-07-31.
- ^ "Microcontroller Interfaces, Part 3". 090114 ucpros.com
- ^ "Ujjal's DMX512 Pages....DMX512 Physical properties". 090610 dmx512-online.com
- ^ "DMX Wiring and Practice Quick Reference".
- ^ http://www.diva-portal.org/smash/get/diva2:1162587/FULLTEXT02 "Implementing and Analyzing SingleEdge Nibble Transmission (SENT)Protocol for Automotive Applications", Master thesis of Naseem Ullah, 2014
- ^ Strasser, Michael; Rasbornig, Friedrich; Platzdasch, Hagen; Gastinger, Ferdinand; Eggiman, Christoph; Beaurenaut, Laurent (2009-04-20). "Single-Edge Nibble Transmission: Challenges and Evolutions". SAE Technical Paper Series. Vol. 1. Warrendale, PA. doi:10.4271/2009-01-0125.
{{cite book}}
: CS1 maint: location missing publisher (link)