![](https://upload.wikimedia.org/wikipedia/commons/thumb/6/6e/Draw_plates-two.jpg/220px-Draw_plates-two.jpg)
A draw plate is type of die consisting of a hardened steel plate with one or more tapered holes through which wire is drawn to make it thinner. A typical plate will have twenty to thirty holes, so a wide range of diameters can be drawn.[1]
Drawing wire
[edit]![](https://upload.wikimedia.org/wikipedia/commons/thumb/4/46/Wiredrawing.jpg/220px-Wiredrawing.jpg)
Before drawing, the draw plate is held securely in a vise or other fixture. The plate is oriented so that the wider end of a tapered opening can receive a metal wire which is to be pulled through it.
Annealed soft, ductile wire is filed at one end to give it an initial taper. The tapered end is inserted into a tapered hole with a final diameter just smaller than its current width. Special pliers, called draw tongs are used to hold the tip of the wire and pull it through, sometimes with the aid of grease or wax as a lubricant. Small-diameter wire may be drawn manually, while very thick wire may require a drawing bench with a crank to produce enough force.
Typically, a wire can be drawn three times in sequence before it needs to be re-annealed. This must be done because drawing wire hardens it, which causes the wire to become brittle. Brittle wire that has not been annealed may snap during the drawing process (or develop microscopic or macroscopic cracks, which may weaken the piece or "grow" with further working).
With a mandrel, a draw plate can be used to draw tubes of metal. Plates are available in many different sizes and shapes for drawing different shapes of wire, including round, square, oval, half-round, and hexagonal.
History
[edit]![](https://upload.wikimedia.org/wikipedia/commons/thumb/f/f9/Bergen_Universitetsmuseet_i_Bergen_Arkeologibasen_B17202-19_saumlo-drawplate.jpg/220px-Bergen_Universitetsmuseet_i_Bergen_Arkeologibasen_B17202-19_saumlo-drawplate.jpg)
The origins of wire-drawing are uncertain. One of the earliest known written references to wire-making is Exodus 39:3, which suggests that gold was hammered into sheets, cut into strips, and then these strips were made into gold wire, but the precise technique is not clear. The oldest clear written descriptions of the method are the twelfth-century De diversis artibus by Theophilus Presbyter and the sixteenth-century De la pirotechnia by Vannoccio Biringuccio. As of 2023, the earliest known draw plates dated to around the sixth century.[2]
See also
[edit]References
[edit]- ^ Littell, Eliakim; Littell, Robert S. (1892), The Living age, vol. 195, Littell, Son and Co., p. 512.
- ^ Wärmländer, Sebastian K. T. S.; Ljungkvist, John; Jahrehorn, Max; Hennius, Andreas (2023-10-01). "A 6th-8th c. wire-drawing iron plate with silver residue from a Vendel Period workshop in Old Uppsala, Sweden". Journal of Archaeological Science: Reports. 51: 104193. Bibcode:2023JArSR..51j4193W. doi:10.1016/j.jasrep.2023.104193. ISSN 2352-409X.
Well, that’s interesting to know that Psilotum nudum are known as whisk ferns. Psilotum nudum is the commoner species of the two. While the P. flaccidum is a rare species and is found in the tropical islands. Both the species are usually epiphytic in habit and grow upon tree ferns. These species may also be terrestrial and grow in humus or in the crevices of the rocks.
View the detailed Guide of Psilotum nudum: Detailed Study Of Psilotum Nudum (Whisk Fern), Classification, Anatomy, Reproduction