![]() | |
Industry | Automobile |
---|---|
Founded | April 11, 1916 |
Defunct | February 23, 1954 |
Fate | Merged |
Successor | Nash-Kelvinator American Motors Corporation |
Headquarters | Kenosha, Wisconsin, United States |
Key people | Charles W. Nash, Nils Erik Wahlberg |
Products | Vehicles |
![](https://upload.wikimedia.org/wikipedia/commons/thumb/f/f0/Nash_Motors_Comp._1919.jpg/220px-Nash_Motors_Comp._1919.jpg)
Nash Motors Company was an American automobile manufacturer based in Kenosha, Wisconsin from 1916 until 1937. From 1937 through 1954, Nash Motors was the automotive division of the Nash-Kelvinator Corporation. As sales of smaller firms declined after 1950 in the wake of the domestic Big Three automakers’ (General Motors, Ford, and Chrysler) advantages in production, distribution, and revenue, Nash merged with Hudson Motors to form American Motors Corporation (AMC).[1] Nash automobile production continued from 1954 through 1957 under AMC.
Innovations by Nash included the introduction of an automobile heating and ventilation system in 1938 that is still used today, unibody construction in 1941, seat belts in 1950, a U.S.-built compact car in 1950, and an early muscle car in 1957.[2]
History
[edit]![](https://upload.wikimedia.org/wikipedia/commons/thumb/0/0c/Glendale-1917_Nash_Fire_Truck.jpg/220px-Glendale-1917_Nash_Fire_Truck.jpg)
![](https://upload.wikimedia.org/wikipedia/commons/thumb/4/45/1922-nash-001.jpg/220px-1922-nash-001.jpg)
Nash Motors was founded in 1916 by former General Motors president Charles W. Nash, who acquired the Thomas B. Jeffery Company.[3] Jeffery's best-known automobile was the Rambler whose mass production from a plant in Kenosha began in 1902.
The 1917 Nash Model 671 was the first vehicle produced to bear the name of the new company's founder.[4] Sales for 1918 were 10,283 units. More models were added in 1919, and sales rose to 27,081.
The decades of success enjoyed by Nash were said to be due to its focus on building cars "embodying honest worth [at] a price level which held out possibilities of a very wide market."[5]
The four-wheel drive Jeffery Quad truck became an important product for Nash. Approximately 11,500 Quads were built between 1913 and 1919. They served to move material during World War I under severe conditions. The Quad used Mehul differentials[6] with half-shafts mounted above the load-bearing dead axles to drive the hubs through hub-reduction gearing.[7] In addition, it featured four-wheel steering.[8] The Quad achieved the reputation of being the best four-wheel drive truck produced in the country.[9] The newly formed Nash Motors became the largest producer of four-wheel drives.[10] By 1918, capacity constraints at Nash meant the Paige-Detroit Motor Car Company began to assemble the Nash Quad under license and Nash patents.[11] Nash became the leading producer of military trucks by the end of World War I.[12] After the War ended, surplus Quads were used as heavy work trucks in fields such as construction and logging.[13]
Charles Nash convinced the chief engineer of GM's Oakland Division, Finnish-born Nils Eric Wahlberg, to move to Nash's new company.[14] The first Nash engine introduced in 1917 by Wahlberg had overhead valves,[14] which Nash had learned about while working for Buick. Wahlberg is also credited with helping design the flow-through ventilation used since then in nearly every motor vehicle.
Introduced in 1938, Nash's Weather Eye directed fresh, outside air into the car's fan-boosted, filtered ventilation system, where it was warmed (or cooled), and then removed through rearward placed vents.[15] The process also helped to reduce humidity and equalize the slight pressure differential between the outside and inside of a moving vehicle.
Another unique feature of Nash cars was the unequal wheel tracks. The front wheels were set slightly narrower than the rear, thus adding stability and improving cornering. Wahlberg was also an early proponent of wind tunnel testing for vehicles and, during World War II, worked with Theodore (Ted) Ulrich in the development of Nash's radically styled Airflyte models.[16]
Nash's slogan from the late 1920s and 1930s was "Give the customer more than he has paid for," and the cars lived up to it. Innovations included a straight-eight engine with overhead valves, twin spark plugs, and nine crankshaft bearings in 1930. The 1932 Ambassador Eight had synchromesh transmissions and free wheeling, automatic centralized chassis lubrication, a worm-drive rear end, and its suspension was adjustable inside the car. A longtime proponent of automotive safety, Nash was among the early mid- and low-priced cars that offered four-wheel brakes.
The Nash was a success among consumers, which meant for the company, "selling for a long time has been 100% a production problem... month after month, all the cars that could be produced were sold before they left the factory floor."[5]
Development of the Ajax
[edit]For the 1925 model year, Nash introduced the entry-level marque Ajax. The Ajax was produced in the newly acquired Mitchell Motor Car Company plant in Racine, Wisconsin. Mitchell was the manufacturer of Mitchell-brand automobiles between 1903 and 1923. Sales of Ajax automobiles, while quite respectable, were disappointing. It was believed that the same car would sell better if it were called a Nash. Thus, the Ajax became the "Nash Light Six" in June 1926, and sales improved as expected.
In an unusual move, Nash Motors offered all Ajax owners a kit to "convert" their Ajax into a Nash Light Six. This kit, supplied at no charge, included a set of new hubcaps, a radiator badge, and all other parts necessary to change the identity of an Ajax into that of a Nash Light Six. This was done to protect Ajax owners from the inevitable drop in resale value when the Ajax marque was discontinued. In this way, Nash Motors showed high value for its customers' satisfaction and well-being. Most Ajax owners took advantage of this move, and "unconverted" Ajax cars are rare today.
Acquisition of LaFayette
[edit]Nash was the principal stockholder in LaFayette Motors, a company started in Indianapolis, Indiana in 1920. It later moved to Milwaukee, Wisconsin, and became the producer of a large, powerful, and expensive luxury car. Other significant stockholders were Charles W. Nash and his friends and business associates. However, the LaFayette cars did not sell well.
In 1924, Nash absorbed LaFayette and converted its plant to produce Ajax automobiles. The LaFayette marque was reintroduced in 1934 as a lower-priced companion to Nash. LaFayette ceased to be an independent marque with the introduction of the 1937 models. From 1937 through 1940, the Nash LaFayette was the lowest-priced model, replaced by the new unibody Nash 600 for the 1941 model year.
Era of George Mason and Nash Kelvinator
[edit]![](https://upload.wikimedia.org/wikipedia/commons/thumb/c/c7/Nash_Special_Six_Coupe_1929.jpg/220px-Nash_Special_Six_Coupe_1929.jpg)
![](https://upload.wikimedia.org/wikipedia/commons/thumb/c/ce/Nash_Convertible_Coupe_1929.jpg/220px-Nash_Convertible_Coupe_1929.jpg)
Before retiring, Charles Nash chose Kelvinator Corporation head George W. Mason to succeed him. Mason accepted, but placed one condition on the job: Nash would acquire controlling interest in Kelvinator, which at the time was the leading manufacturer of high-end refrigerators and kitchen appliances in the United States. As of 4 January 1937, the resulting company was known as Nash-Kelvinator. As a brand name, Nash continued representing automobiles for the merged firm. This was the largest merger of companies in two different industries until then.
In 1938, Nash introduced an optional conditioned air heating/ventilating system, an outcome of the expertise shared between Kelvinator and Nash. This was the first hot-water car heater to draw fresh air from outside the car and is the basis of all modern internal combustion engine car heaters in use today. Also in 1938, Nash, along with other car manufacturers Studebaker and Graham, offered vacuum-controlled shifting, an early approach to removing the gearshift from the front floorboards. Automobiles equipped with the Automatic Vacuum Shift (supplied by the Evans Products Company) had a small gear selector lever mounted on the dashboard, immediately below the radio controls.
In 1936, Nash introduced the "Bed-In-A-Car" feature, which converted the car's interior into a sleeping compartment. The rear seatbacks were hinged to go up, allowing the back seat cushion to be propped up into a level position. This also created an opening between the passenger compartment and the trunk. Two adults could sleep in the car with their legs and feet in the trunk and their heads and shoulders on the rear seat cushions. In 1949, this arrangement was modified so that fully reclining front seatbacks created a sleeping area within the passenger compartment. In 1950, these reclining seatbacks were made to lock into several intermediate positions. Nash soon called these "Airliner Reclining Seats".
In 1939, Nash added a thermostat to its "Conditioned Air System", and thus the famous Nash Weather Eye heater was introduced. The 1939 and 1940 Nash streamlined cars were designed by George Walker and Associates and freelance body stylist Don Mortrude. They were available in three series - LaFayette, Ambassador Six, and Ambassador Eight. For the 1940 model cars, Nash introduced independent coil spring front suspension and sealed beam headlights.
Introduced for the 1941 model year, the Nash 600 was the first mass-produced unibody construction automobile made in the United States. Its lighter weight compared to body-on-frame automobiles and lower air drag helped it to achieve excellent fuel economy for its day. The "600" model designation is said to have been derived from overdrive-equipped examples of this car's ability to travel 600 miles (966 km) on a 20-US-gallon (75.7 L; 16.7 imp gal) tank of gasoline. It would achieve 30 miles per US gallon (7.8 L/100 km; 36 mpg‑imp). The 600 models used an unusual steering/front suspension system with extremely long kingpins. Inadequate lubrication became a problem for these systems, commonly resulting in premature failures. The design of the cars was improved by new front ends, upholstery, and chrome trim from 1942 through 1948. The larger Ambassador models shared the same bodies with the 600 but placed this unibody structure on top of a conventional frame, resulting in a robust design.
Post-World War II passenger car production resumed on 27 October 1945, with an Ambassador sedan first off the assembly line. There were a few changes from the 1942 models. The extended, slimmer upper grille bars and a projecting center section on the lower grille were most noticeable. The 600 models featured a conventional front suspension and steering system. Postwar Nashes were six-cylinder only; eight-cylinder engines did not return. The large Ambassador engine thus was the seven main bearing, overhead-valve, 234-cubic-inch (3.83 L), six-cylinder developing 112 bhp (84 kW; 114 PS).
Nash was considering the potential of offering a pickup truck and developed a prototype built on the existing chassis with a modified 600 front end and cab along with an outsourced cargo bed.[17] For the 1946 model year, Nash introduced the Suburban model that used wood framing and panels on the body. It was similar to the Chrysler Town and Country and Ford Sportsman models. Suburbans were continued in 1947 and 1948, with 1,000 built over the three years. In 1948, the Ambassador convertible returned with 1,000 made.
Introduction of the Nash Airflyte
[edit]![](https://upload.wikimedia.org/wikipedia/commons/thumb/5/55/Nash_Stateman_2-Door_Sedan_1951.jpg/220px-Nash_Stateman_2-Door_Sedan_1951.jpg)
![](https://upload.wikimedia.org/wikipedia/en/thumb/4/43/NashMotorsLogo.jpg/150px-NashMotorsLogo.jpg)
The aerodynamic 1949 Nash "Airflyte" was the first car of an advanced design introduced by the company after the War. Its aerodynamic body shape was developed in a wind tunnel. A "radically aerodynamic" format was first proposed around 1943 by two independent designers, Ted Pietsch and Bob Koto, to Nash's vice president of engineering, Nils E. Wahlberg.[18] The resulting all-new 1949 production cars were similar to the proposed sketches.[18] The objective was to reduce the automobile's body's drag coefficient by using a smooth shape and enclosed front fenders.[19] Closed fenders were conceived by Nash engineers also in the exploration for added strength of unibody construction. In contrast, Hudson, a close competitor, incorporated an actual unibody frame section into its closed rear wheel openings at about the same time.[citation needed] The "cutting-edge aerodynamics" of the all-new postwar design were the most "alarming" in the industry since the Chrysler Airflow.[20] It was built at one of two new factories in El Segundo, California, where the factory is still being used, having been re-purposed as the Boeing Satellite Development Center, immediately south of Los Angeles International Airport, on Nash Street.
A one-piece curved safety glass windshield was used on both models. Wide and low, the automobile featured more interior room than its 1948 predecessor, although its height was 6 inches lower. Due to its enclosed front fenders, Nash automobiles had a larger turning radius than most other cars. The 600 models used a 112-inch (2,800 mm) wheelbase while the Ambassador models stretched to 121 inches (3,073 mm). Both shared the same bodies. Coil springs were used on all four wheels. Both models offered Three trim lines: Super, Super Special, and the top-line Custom. Power was provided by an 82-horsepower (61 kW), 176-cubic-inch (2.88 L) flathead I6 cylinder in the 600 and a 112-horsepower (84 kW) OHV, 234-cubic-inch (3.83 L) I6 in the Ambassador.
In 1949, Nash became the first American car with seat belts as a factory option.[21] They were installed in 40,000 cars, yet buyers did not want them and had dealers remove them.[22] There was "heated debate despite increasing scientific research" about their value and the option was "met with insurmountable sales resistance" with Nash reporting that after one year "only 1,000 had been used" by customers.[21][22]
The few changes for the 1950 Airflytes were a wider rear window, concealed fuel filler cap, some dashboard features, and the addition on Ambassadors of a GM Hydramatic automatic transmission option. The 600 models were renamed the "Statesman". A five-position "Airliner" reclining front passenger seatback was optional for both models. The stroke on the Statesman engine was increased 1/4 inch, giving 186 cubic inches (3.05 L) and 85 hp (63 kW), and the Ambassador received a new cylinder head that increased hp to 115.
Changes for the 1951 model Airflytes were to the rear fenders, elongated to incorporate vertical taillights, a new conventional dashboard replacing the Uniscope mounted on the steering column, and a new upright bar grille with horizontal parking lights as well as the addition of GM Hydramatic as a Statesman option. The three best sales years for Nash up to that time were 1949, 1950, and 1951.
![](https://upload.wikimedia.org/wikipedia/commons/thumb/3/3e/1950-nash-001.jpg/220px-1950-nash-001.jpg)
![](https://upload.wikimedia.org/wikipedia/commons/thumb/9/9b/AlgiersMetropolitan1_cropped.jpg/220px-AlgiersMetropolitan1_cropped.jpg)
Nash-Kelvinator's president, George Mason, felt Nash had the best chance of reaching a larger market by building small cars. He directed Nash towards developing the first compact of the post-war era, the 1950 Nash Rambler, which was marketed as an up-market, feature-laden convertible. Mason orchestrated a contract manufacturing arrangement with Austin of the UK to build Nash's new subcompact car, the Metropolitan. It was introduced in March of 1954.[26]
The full-size Nash Airflytes were wholly re-designed for the 1952 model year. They were promoted as the Golden Airflytes in honor of Nash Motors' 50th anniversary as an automobile builder because the company was counting the years of the Thomas B. Jeffery Company as part of their heritage. Therefore, "Great Cars Since 1902" became one of the company's advertising slogans. Nash was the only American car manufacturer besides Ford Motor Company to introduce an all-new 1952 model.
The new Golden Airflytes presented a more modern, squared-off look than did the 1949 through 1951 models, which were often compared to inverted bathtubs. Nash contracted Battista "Pinin" Farina of Italy to design a body for the new Golden Airflyte. Management wanted a better design, and the result was a combination of an in-house design and Pinin Farina's model. Also in 1952, Nash began offering automatic transmissions, either a GM Hydramatic or a Borg-Warner overdrive transmission. Power was provided by a six-cylinder engine that was now bored out to 252 cubic inches (4.13 L).
Using its Kelvinator refrigeration experience, the automobile industry's first single-unit heating and air conditioning system was introduced by Nash in 1954.[27] This was a compact, affordable system for the mass market with controls on the dash and an electric clutch.[28] Entirely incorporated within the engine bay, the combined heating and cooling system had cold air for passengers enter through dash-mounted vents.[27] Competing systems used a separate heating system and an engine-mounted compressor with an evaporator in the car's trunk to deliver cold air through the rear package shelf and overhead vents. The alternative layout pioneered by Nash "became established practice and continues to form the basis of the modern and more sophisticated automatic climate control systems."[29]
Introduction of the Nash-Healey
[edit]The Anglo-American Nash-Healey sports car was introduced in 1951. This was a collaborative effort between George Mason and British sports car manufacturer Donald Healey. Healey designed and built the chassis and suspension and, until 1952, the aluminum body, which another British manufacturer, Panelcraft Sheet Metal Co. Ltd., fabricated in Birmingham West Midlands. Nash shipped the powertrain components to England, and Healey assembled the cars, then shipped finished vehicles to the U.S. In 1952, the Italian designer Battista Farina restyled the body, and its construction changed to steel and aluminum. High costs, low sales, and Nash's focus on the Rambler line led to the termination of Nash-Healey's production in 1954 after 506 automobiles had been produced.
While a welcome attempt to improve Nash's stodgy image, the Nash-Healey did little to enhance showroom traffic as Nash sales fell steadily from 1951 onward. The Airflyte had initially sold well in the postwar "seller's" market. Still, its bulbous styling, rooted in 1940s design trends, quickly became passé, and its underpowered six-cylinder engine proved to be a significant liability against GM's new OHV short-stroke V8s. Like fellow independents Hudson, Studebaker, and Packard, Nash charged higher prices for their cars than Ford and GM, which benefited from the economies of scale. The independents also lacked the Big Three's extensive dealer network or advertising budget. Low-profit Rambler sales gradually made up more and more of Nash's total production. In 1953 and 1954, Ford and GM also waged an all-out price war on each other, further damaging the independents' sales. Mainline Nashes also lacked body styles; despite introducing a hardtop coupe in 1952, there was no convertible or station wagon, although the Rambler lineup featured all of these versions.
In addition, while Nash had profited from military contracts during the Korean War, that conflict ended in mid-1953. At the same time, the new Secretary of Defense Charles E. Wilson, ex-GM president, began steering defense contracts to his former employer at the expense of the rest of the automotive industry.
Mason commissioned Farina to design a Rambler-based two-seater coupe called the Palm Beach, which may have been intended as a successor to the Nash-Healey. However, the project only progressed to a concept car.[30]
For European endurance racing, Healey and his staff designed and built three special Nash-Healeys with lightweight aluminum racing bodies. These competition versions entered four consecutive Le Mans races and one Mille Miglia. At Le Mans, they achieved fourth overall in 1950, sixth overall and fourth in class in 1951, third overall and first in class in 1952, and eleventh overall in 1953. In the Mille Miglia, they finished ninth overall in 1950 and seventh overall, as well as placing fourth in class in 1952.
Formation of American Motors Corporation
[edit]![](https://upload.wikimedia.org/wikipedia/commons/thumb/b/bf/Nash_Rambler_Cross_Country_1955.jpg/220px-Nash_Rambler_Cross_Country_1955.jpg)
In January 1954, Nash announced the acquisition of the Hudson Motor Car Company as a friendly merger, creating American Motors Corporation (AMC). To improve the financial performance of the combined companies, all production, beginning with the 1955 Nash and Hudson models, would happen at Nash's Kenosha plant. Nash would focus most of its marketing resources on its smaller Rambler models, and Hudson would focus its marketing efforts on its full-sized cars.
One of the first things Mason did as CEO of the new company was to initiate talks with James J. Nance, president of Packard, for parts-sharing arrangements between AMC and Packard. At this time, AMC did not have its own V8 engine, and an agreement was made for the new 320 cu in (5.2 L) Packard V8 engine and Packard's Ultramatic automatic transmission to be used in the 1955 Nash Ambassador and Hudson Hornet models.
In July 1954, Packard acquired Studebaker to form Studebaker-Packard Corporation,[31] however, further talks of a merger between AMC and Packard-Studebaker were cut short when Mason died on 8 October 1954. A week after his death, Mason's successor, George W. Romney, announced "there are no mergers under way either directly or indirectly".[32] Nevertheless, Romney continued with Mason's commitment to buy components from Studebaker-Packard Corporation. Although Mason and Nance had previously agreed that Studebaker-Packard would purchase parts from AMC, it did not do so. Moreover, Packard's engines and transmissions were comparatively expensive, so AMC began development of its own V8 engine, and replaced the outsourced unit by mid-1956.[33]
For the 1955 model year, all the large Nash and Hudson automobiles were based on a Nash-derived shared unitized body shell using styling themes by Pinin Farina, Edmund E. Anderson, and Frank Spring. Each had individual powertrains and separate, non-interchangeable body parts.[34] This mimicked the longtime practice Big Three (General Motors, Ford, and Chrysler) that allowed for maximum manufacturing economy. Anderson set up separate design studios for Nash, Hudson, and Rambler.
George Romney ordered the removal of the front fender skirts on Nashes and Ramblers for the 1955 models. Customers disliked this feature, yet it was reportedly demanded by George Mason, who liked their appearance.
Even with the merger forming AMC, they were held to a total of about four percent of the market and thus were under pressure to lower expenses and tooling costs for new models, perhaps by innovation.[35]
The Nash Metropolitan, marketed under either the Nash or Hudson brands, became a make unto its own in 1957, as did the Rambler. By this point, Rambler sales comprised most of AMC's volume, so George Romney decided to phase out the Nash and Hudson nameplates and focus solely on Rambler. This move would pay off the following year when an economic recession struck the United States and created a strong demand for economical compact cars.[36] Nash and Hudson production ended with the last Hornet made on 25 June, 1957.[37] From 1958 until 1962, Rambler and the Metropolitan were the only brands of cars sold by AMC. By 1965, the Rambler name would begin to be phased out, and AMC would take over as the brand name until the 1988 model year.
In 1970, American Motors acquired Kaiser Jeep (the descendant of Willys-Overland Motors) and its Toledo, Ohio, based manufacturing facilities. In 1979, AMC established a technology partnership with Renault. In 1987, Chrysler Corporation made a public offering to acquire all shares of AMC on the NYSE. The shareholders approved the offer, and AMC became a division of Chrysler Corporation.
International markets
[edit]Since the early days, Nash vehicles were exported as complete cars or in knock-down kit form for local assembly to many countries around the world including right-hand-drive markets such as the United Kingdom,[38] Australia, New Zealand, and South Africa. International production for both the Nash and Hudson Marques was consolidated after the merger of Nash and Hudson to form American Motors Corporation (AMC) in 1954, after which international-bound operations were conducted at the former Nash factory in Kenosha and the Brampton plant in Canada until 1957, when both the Nash and Hudson Marques were retired.
Australia
[edit]Several distributors for each Australian state built and sold Nash vehicles in the 1920s. As was the practice for all car brands during the early 20th Century, the chassis and engines were imported, and Australian coach builders locally built the bodies. Early distributors were Wilsford Limited for New South Wales,[39] Richards Brothers for Victoria and the Riverina,[40] Peels Limited for Queensland,[41] Eric Madren Motors (later Nash Cars (W.A) Limited) for Western Australia,[42] and Northern Motors for Tasmania.[43] The recovery period following the end of World War II saw a lull in car manufacturing, petrol rationing, and currency shortages. Some cars were imported in the late 1940s and 1950s despite these factors. In 1950, a few Nash trucks were assembled by Davies Pty Ltd in Launceston, Tasmania.
After the Nash-Hudson merger in 1954, AMC's new Rambler vehicles were imported into Australia and distributed by Ira L. & A.C Berk Pty Ltd[44] which had previously held the Hudson franchise since 1939. Hudson was the more recognized brand in Australia, so they were initially sold as Hudson. The Nash Metropolitan was not sold in Australia. The first Rambler-badged vehicles were imported in 1957. This first shipment consisted of 24 cars, 10 of which were Rambler station wagons. Small numbers of Rambler Sixes were imported into Australia up until 1960. AMC made a new deal with Port Melbourne vehicle assembler Australian Motor Industries (AMI) in 1960 to build AMC vehicles from knock-down kits, production of which ran from 1961 until 1976. AMI eventually became Toyota Australia.
New Zealand
[edit]From 1935, Nash motor vehicles were assembled in New Zealand by Christchurch company Motor Assemblies Limited. The plant also made Studebaker and Standard vehicles and was acquired by Standard Motors in 1954.[45] Production was then moved to Auckland company VW Motors at their Volkswagen plant in Otahuhu, Auckland until 1962.[46] New Zealand saw the Nash Ramblers and the British-built, right-hand-drive Nash Metropolitan. In 1963, AMC struck a deal with Thames company Campbell Motors to build a new vehicle assembly plant for AMC vehicles, which began production in 1964. Renamed Campbell Motor Industries (CMI), the plant built Rambler vehicles from knock-down kits until 1971. CMI eventually became "Toyota New Zealand".
South Africa
[edit]Following World War II, Nash motor vehicles were assembled in South Africa by a newly built assembly operation in East London Car Distributors and Assemblers (CDA). The plant also built Packard, Renault, and Standard motor vehicles. CDA was eventually taken over, first by Chrysler, and finally by Peugeot.[47]
United Kingdom
[edit]Nash vehicles were imported into the United Kingdom by London company Nash Concessionaires.[48][49] After 1961, Rambler imports switched to the former U.K Hudson operation in Chiswick which was accordingly renamed Rambler Motors (A.M.C.) Limited.[50] AMC's deal with Austin for the production of the Nash Metropolitan was independent of the Chiswick Rambler operation.
Gallery
[edit]-
Nash Six Touring 1927
-
Nash Standard Six Series 420 4-Door Sedan 1929
-
Nash Single Six Series 450 4-Door Sedan 1930
-
Nash Twin-Ignition Six Series 481 Convertible Coupé 1930
-
Nash Series 871 Convertible Sedan 1931
-
Nash Ambassador Eight 4-Door Sedan 1934
-
Nash Advanced Six Series 3520 4-Door Sedan 1935
-
Nash 3540 400 4-Door Sedan 1935
-
Nash 3540 400 4-Door Sedan 1935
-
Nash Lafayette Series 3610 4-Door Sedan 1936
-
Nash Ambassador Six 3620 4-Door Sedan 1936
-
Nash 4-Door Sedan
-
Nash Ambassador Six Series 3728 4-Door Sedan 1937
-
1937 Nash Lafayette in New Zealand
-
Nash Lafayette Series 3818 4-Door Sedan 1938
-
Nash Ambassador Six Series 3828 4-Door Sedan 1938
-
Nash 2-Door Sedan 1940
-
Nash Ambassador Six four-door sedan 1941
-
Nash 4-Door Sedan 1946
-
Australian right-hand drive 1957 Nash Rambler wagon
-
New Zealand right-hand drive 1959 Nash Metropolitan
-
Detail from a Nash Metropolitan
-
Nash dealership in Alabama, ca. 1930-1945
Nash automobile brands
[edit]Nash automobiles
[edit]- Nash 600
- Nash Statesman
- Ambassador
- Metropolitan
- Nash-Healey, in cooperation with Donald Healey, was assembled in the UK and Italy.
- Nash Rambler
- Rambler
Motorsport
[edit]Like most American manufacturers of the fifties, Nash participated in the Grand National Stock Car series.
See also
[edit]- Pratt & Whitney R-2800 Double Wasp, Nash built during WWII
References
[edit]- Inline
- ^ Perschbacher, Gerald (11 January 2021). "Merger Mania: Nash and Hudson form AMC". Old Cars Weekly. Retrieved 2 February 2023.
- ^ Foster, Patrick R. (2004). AMC cars, 1954-1987: an illustrated history. Iconografix. p. 158. ISBN 978-1-58388-112-5.
- ^ "Charles W. Nash and the Nash Motor Company". Wisconsin Historical Society. 3 August 2012. Retrieved 2 February 2023.
- ^ Lewis, Albert L.; Musciano, Walter A. (1977). Automobiles of the World. Simon and Schuster. p. 280. ISBN 978-0-671-22485-1.
- ^ a b Forbes, B.C.; Foster, O.D. (2003) [1926]. Automotive Giants of America: Men Who Are Making Our Motor Industry. Kessinger Publishing. pp. 211–224. ISBN 978-0-7661-6177-1.
- ^ American industries, Volume 14. National Association of Manufacturers (U.S.). 1903. p. 124. Retrieved 27 January 2023 – via Google Books.
- ^ "Jeffrey Quad". 4wdonline.com. Archived from the original on 22 October 2012. Retrieved 27 January 2023.
- ^ Eckermann, Erik (2001). World history of the automobile. Society of Automotive Engineers. p. 76. ISBN 978-0-7680-0800-5.
- ^ "New York Curb and Industrial Issues". Copper Curb and Mining Outlook. Vol. 14, no. 18. 24 January 1917. p. 15. Retrieved 27 January 2023 – via Google Books.
- ^ Botti, Timothy J. (2006). Envy of the world: a history of the U.S. economy & big business. Algora Publishing. p. 188. ISBN 978-0-87586-432-7. Retrieved 27 January 2023 – via Google Books.
- ^ Keller, Michael E. (1998). The Graham Legacy: Graham-Paige to 1932. Turner Publishing. ISBN 978-1-56311-470-0. Retrieved 27 January 2023 – via Google Books.
- ^ Flink, James J. (1990). The Automobile Age. MIT Press. p. 102. ISBN 978-0-262-56055-9. Retrieved 27 January 2023 – via Google Books.
- ^ Fregulia, Carolyn (2008). Logging in the Central Sierra. Arcadia Publishing SC. p. 86. ISBN 978-0-7385-5816-5. Retrieved 27 January 2023 – via Google Books.
- ^ a b Norbye, Jan P. (1981). The 100 greatest American cars. TAB Books. ISBN 978-0-8306-9623-9. Retrieved 27 January 2023 – via Internet Archive.
- ^ Wolfe, Steven J. (2000). "HVAC Time Line". Refrigeration Service Engineers Society Twin Cities Chapter. Archived from the original on 21 November 2009. Retrieved 18 June 2010.
- ^ Automobiles of the '50s. Publications International. 1993. p. 63. ISBN 978-0-7853-2008-1.
- ^ "1946 Nash P1 Pickup For Sale". carandclassic.co.uk. Retrieved 2 February 2023.
- ^ a b Foster, Patrick R. (1998). "The Designers". The Nash Styling Sketchbook. The Olde Milford Press. p. 1. ISBN 978-0-9662019-0-1. Retrieved 14 April 2022.
- ^ Crittenden, Bill. "Airflyte". The Crittenden Automotive Library. Retrieved 2 February 2023.
- ^ Mueller, Mike (1997). Fifties American Cars. MBI Publishing. p. 67. ISBN 978-0-87938-924-6.
- ^ a b Janik, Erika (25 September 2017). "The Surprisingly Controversial History Of Seat Belts". Wisconsin Public Radio. Retrieved 2 February 2023.
- ^ a b Ronan, Larry (April 1979). Seatbelts: 1949-1956. U.S. Department of Transportation, National Highway Traffic Safety Administration (DOT-TSC-NHTSA-79-1). p. 17.
- ^ "1951 Rambler Custom Landau". auto.howstuffworks.com. 27 May 2007. Archived from the original on 15 August 2020. Retrieved 2 February 2023.
- ^ "Lois Lane's 1950 Nash Rambler Custom". articboy.com. Retrieved 2 February 2023.
- ^ Donnelly, Jim (June 2005). "TV Cars". Hemmings Classic Car. Retrieved 2 February 2023.
- ^ "1954 Nash Metropolitan". Drives.Today. 25 August 2022. Retrieved 2 February 2023.
- ^ a b Binder, Al; Ward's staff (1 February 2001). "Rearview Mirror". Ward's AutoWorld. Archived from the original on 24 November 2011. Retrieved 2 February 2023.
- ^ Daly, Steven (2006). Automotive Air-Conditioning and Climate Control Systems. Elsevier Science & Technology Books. p. 2. ISBN 978-0-7506-6955-9.
- ^ Nunney, Malcolm J. (2006). Light and Heavy Vehicle Technology. Elsevier Science & Technology Books. p. 147. ISBN 978-0-7506-8037-0.
- ^ "AMX Palm Beach". auto.howstuffworks.com. 15 October 2007. Archived from the original on 8 August 2020. Retrieved 2 February 2013.
- ^ "Autos: Merger No. 3". Time. 28 June 1954. Retrieved 3 June 2024.
- ^ "Personnel: Changes of the Week". Time. 25 October 1954. Retrieved 3 June 2024.
- ^ "Autos: New Entry". Time. 24 March 1954. Retrieved 3 June 2024.
- ^ Donovan, Leo (January 1955). "Detroit Listening Post". Popular Mechanics. Vol. 103, no. 1. p. 110. Retrieved 3 June 2024 – via Google Books.
- ^ Donovan, Leo (August 1954). "Detroit Listening Post". Popular Mechanics. Vol. 102, no. 2. p. 82. Retrieved 3 June 2024 – via Google Books.
- ^ Lamm, Michael; Holls, Dave (1996). A century of automotive style: 100 years of American car design. Lamm-Morada. pp. 201–202. ISBN 978-0-932128-07-2. Retrieved 3 August 2015.
- ^ Flory, Jr., J. "Kelly" (2008). American Cars, 1946-1959 Every Model Every Year. McFarland. p. 815. ISBN 978-0-7864-3229-5. Retrieved 3 August 2015.
- ^ "The Cars at Earls Court". motorsportmagazine.com. 7 July 2014. Retrieved 13 November 2021.
- ^ "The New Nash". The Sun. Sydney, NSW. 22 November 1924. p. 8. Retrieved 2 February 2023 – via Trove.
- ^ "Motors Here". Farmers' Advocate. Melbourne, Victoria. 14 September 1923. p. 6. Retrieved 2 February 2023 – via Trove.
- ^ "Nash Motor Cars". The Brisbane Courier. Qld. 12 August 1922. p. 12. Retrieved 2 February 2023 – via Trove.
- ^ "Nash Motors". Truth. Perth, WA. 22 December 1929. p. 11. Retrieved 2 February 2023 – via Trove.
- ^ "Nash Cars". Daily Telegraph. Launceston, Tas. 3 October 1923. p. 11. Retrieved 2 February 2023 – via Trove.
- ^ "Ira L. and A.C. Berk". Evening News. Sydney, NSW. 13 January 1928. p. 14. Retrieved 2 February 2023 – via Trove.
- ^ Rose, William Dennis (1971). Development options in the New Zealand motor car assembly industry. New Zealand Institute of Economic Research. Research paper; no. 16. Retrieved 2 February 2023.
- ^ Niall, Todd (6 October 2018). "The empty halls of New Zealand's car assembly industry". Stuff. New Zealand. Retrieved 2 February 2023.
- ^ "Motor Assemblies Limited". Motor-assemblies.blogspot.com. 24 January 2012. Retrieved 13 November 2021.
- ^ "Retro Ads - Rambler Classic & American". Classicsworld.co.uk. 6 October 2017. Retrieved 13 November 2021.
- ^ "The cars at Earls Court". Motorsportmagazine.com. 7 July 2014. Retrieved 13 November 2021.
- ^ "Rambler Motors - Graces Guide". gracesguide.co.uk. Retrieved 13 November 2021.
- General
- Gunnell, John, ed. (1987). The Standard Catalog of American Cars 1946–1975. Krause Publications. ISBN 978-0-87341-096-0.
External links
[edit]- Nash Car Club of America (NCCA)
- "Nash Healy History". americansportscars.com/. Archived from the original on 2 June 2023. Retrieved 6 November 2023.
- "The Nash GB Site". Archived from the original on 23 April 2013. Retrieved 19 January 2022.
- The Nordic Nash Register
- Dworschack, Jim; Knutsen, Jerry (16 November 2020). "Nash Engines". allpar.com. Retrieved 6 November 2023.